The interface on the monitor, aka the parent unit, is basic, simple, and intuitive, while many of its competitors have awkward controls. When panning and tilting the camera, for example, the Infant Optics responds immediately and can move in very small increments. The text on the menu displays look like something off an old Motorola RAZR, but the commands are easy to interpret and less confusing than those of some competitors. A group of four buttons makes it easy to pull up the menu and make a change (to the volume, say) without losing sight of the image on the screen. Other nice minor touches, like a display that constantly notes the temperature in the baby’s room, appear on this model but not on all of its competitors. This is not a touchscreen, but frankly, if you’ve ever used an iPhone, you’ll find the touchscreens on most baby monitors to be sorely substandard.
A WiFi monitor gets rid of the parent unit entirely and replaces it with a smartphone app. That app connects to the baby unit over the internet, rather than standard radio frequencies. As a result, you’ll never have to worry about being out of range from your camera. If you’re at dinner and want to check in on the babysitter, you’re still connected. Since it operates from an app, it’s also easier to flip through features than trying to figure out a finicky, low-quality touchscreen, or a dozen different buttons.
Wireless devices and dirty electricity are almost impossible to get away from in our current technological age, but it doesn't mean we can't take steps to limit the exposure to ourselves and our children. Even though the current evidence is somewhat conflicting, and shows we need more studies and research because the potential is there for harm, parents should make informed and thoughtful decisions regarding their children's exposure to potential health risks, especially given that their bodies are developing and more susceptible to this type of radiation. We can't say for certain that monitors pose a health risk, but we also can't say for certain that they don't. Given this information, we feel it is important to test and report on the EMF levels of each monitor so parents can decide for themselves which product fits in best with their goals and concerns.
The HelloBaby might be a standard monitor, but it excels at the basics. It scored better than some of the more expensive WiFi monitors in picture clarity, and was hands-down the easiest to use. Just open the box, plug in the two devices, and you’re ready to go. No difficult packaging to tear through, and no account setup or device pairing necessary. Our testers had it up in running in less than 3 minutes each time.
In our tests, Levana Ayden did well in the categories where Levana Keera underperformed, particularly with regards to user-friendliness. This was most noticeable in the simple controls, which are easy to learn. Levana Ayden also has a few useful extras such as a built-in nightlight and three lullabies to help sooth your baby as they sleep. This unit costs around $90, which is quite competitive with other video baby monitors. Unfortunately, the unit lacks the ability to remotely reposition the camera and has lower than average video quality, which can make details hard to see. The audio had mild interference, but this didn't affect the overall quality much. The one-year warranty is typical of video baby monitors.
There are a few things you can demand from a decent HD video baby monitor, like a crystal clear image and good night vision capabilities. And there are things you can expect of a good Wi-Fi-enabled monitor, like easy remote access from a smart device with real-time streaming audio and video. Then there are things you might hope for from a baby monitor, like two-way talk and solid battery life.
iBaby makes a really confusing range of baby monitors. From cheapest to most expensive this includes the iBaby Monitors M2, M2S, and M2 Plus, iBaby M6, M6T, and M6S, and the new iBaby M7. The M2 series is usually under $100 and is pretty poorly reviewed overall. The M6 series is usually about $125 and is decently reviewed. Finally, the new M7 is brand new and only differs from the M6S in that it has a smell detector and night sky projector that can shine the moon and stars onto the ceiling (our review of the M7 is above). There's truly a lot to love about the iBaby M6S. It looks great, is pretty easy to setup, and has a ton of appealing features. Some highlights are that it uses 1080p high definition video, it senses room temperature and humidity levels, has an air quality sensor (measures the presence of volatile organic compounds or VOCs in the nursery), is dual band wifi compatible (2.4 and 5GHz), and a two-way intercom. It also can record HD videos, remotely pan (rotate) and tilt up/down, and you can setup alerts for motion, sound, and VOCs (from 1 to 4 with 4 being best). So it basically has everything that might be on your list of baby monitor essential features, and we were really excited to set it up. Out of the box, we found it easy to download the app to our smart phone (Android or Apple), connect to the monitor and connect it to wifi, and get things up and running. A couple notes here - first, your wifi password needs to be shorter than 32 characters or the app won't accept it, and second, there is no way to manually set an IP address for the camera. When we used it on our home wifi network, we found that the images were clear and decently fast (low lag), and the night vision was high-quality and not too grainy. We especially liked the pan and tilt features from the app, which allows you to move the camera's view angle around without going into the nursery (and it uses a cool screen-swipe gesture to do it). Once we left our home's wifi connection and tried to connect to the camera from a 4G LTE or a different wifi network, that's when we started to run into problems. It was choppy and laggy, which to be honest is what we expected when attempting to stream 1080p HD video outside of your home network. So we changed the resolution settings on the app (Settings - Display Settings - Resolution) to downgrade it to a lower quality stream; that seemed to help a bit. We also had difficulty connecting to the camera at times, whether we were at home or elsewhere, which was one of the more frustrating things about the iBaby Monitor M6S. The temperature and humidity sensors seemed to work pretty well, and we confirmed their accuracy with a separate thermometer and hygrometer (they were pretty decent in accuracy). For the two-way intercom, the speaker in the camera seemed pretty poor quality so it was hard to hear my voice when attempting to speak to (or sing to) our baby. Finally, we had some issues with alerts coming through to the app as intended. We setup the temperature, humidity, and VOC alerts, and had really intermittent alerts when we tested them out. The temperature and humidity sensors seemed to be reading just fine, they just weren't reliably triggering an alert when they deviated from a range. For example, we set a temperature alert for 80 degrees then blew a hair dryer at the camera; it warmed way up, but the alert wasn't triggered, so that was frustrating. We didn't test the VOC sensor, though one could imagine you could open up a can of paint next to the camera and see if it sends an alert. So overall, we have a decent wifi baby monitor that has some excellent features but also leaves a lot to be desired in the reliability department. Interested? You can check out the iBaby M6S Baby Monitor here.
The Levana Lila is the second highest ranking dedicated monitor in the review, and 5th overall. This budget-friendly option has the longest battery life of any dedicated monitor we tested and scored well enough for ease of use and sound clarity that you won't be frustrated. Unfortunately, this monitor has a shorter range than the Philips Avent SCD630 and the fewest features in the group (which makes it easier to use). So it may not be a good choice for parents that want all the bells and whistles. This monitor does sport 2-way talk to baby, sound activation, and automatic screen wake/sleep, which are some of the most important features in our mind. The Lila has no zoom, and the field of view is rather small for a camera that is not remotely operated (no pan or tilt). However, if you want a dedicated monitor for the simplicity and peace of mind with less chance of a dropped signal, and budget is a factor, then the Lila can't be beaten.
But, for many parents, a baby monitor is a part of daily life. A baby monitor gives you a camera and/or microphone near the crib, and a separate rechargeable parent unit (aka, a monitor) that connects wirelessly and can travel with you throughout the house, either working while plugged in or running off its battery. It's nice to see your children in bed, dreaming happily, sleeping in adorable new positions, cuddling with animals, and generally doing okay.
If you’re absolutely sure you want a Wi-Fi–enabled baby monitor, we found the iBaby M6S to be the best option of the three we tested (the others were the Arlo Baby by Netgear and the Evoz Glow Baby Monitor). The iBaby offers the benefits common to most Wi-Fi monitors and is slightly easier to set up than its competitors. But like its competitors, it shares the significant drawbacks, noted above, that we believe make RF monitors a better choice overall.
Withings features a high-quality 3-MP video sensor that gives clear and unfettered footage of the baby. With special features such as high-resolution digital video, image stabilization, a wide-angle lens, zoom capabilities, and more, you can position the camera in the nursery and not have to worry about constantly repositioning it. In addition to working on Wi-Fi and 3G/4G networks, Withings offers bonus features like a two-way speaker, infrared lighting, the ability to remotely turn on lullabies through the camera itself, motion detection, and room temperature and humidity monitoring. All of this monitoring is done through the complementary Withings apps for iOS and Android.
Security: Whether you’re skeptical of people hacking baby monitors or deeply concerned about it (and there are stories!), the bottom line is that some monitors are at more risk than others. A Wired story from 2015 refers to security firm Rapid7’s findings that Wi-Fi–enabled monitors were particularly vulnerable. We figured people would prefer the not-hackable type, and we talked to a security expert about how to protect your privacy.
You can expect to pay between $30 and $200 for a dedicated video baby monitor, with most branded units costing around $100 on average. Units that allow you to remotely reposition the camera with pan-tilt-zoom functionality are more expensive than those with a fixed view. Wi-Fi video baby monitors don't generally cost extra, because the lack of a specific parent unit balances out the costs of adding Wi-Fi functionality.
In addition to being untested for efficacy, physiologic monitors can increase both your stress and your baby’s stress with false alarms and unnecessary trips to the hospital. Dr. Christopher Bonafide, of the Children’s Hospital of Philadelphia wrote that parents are increasingly bringing healthy babies to the hospital over a false alarm, noting that changes that often set off a monitor are “just normal fluctuations.”
The Nanit couldn’t be more perfect for analytical types. The camera—when placed just so—uses computer vision to watch your baby’s every move, and then tell you what it means. You get a notice on your phone, which acts like a handheld monitor, when your child is awake, acting fussy or has fallen asleep. The Nanit also assigns a sleep score to each night based on how many hours your child was actually crashed out. Other stats include how many times you went into your child’s room and how long it took for your little one to fall asleep. Because the Nanit streams live video and audio to your phone, you can also check in on your kiddo when you’re away from home. It also has a nightlight and temperature and humidity sensors.